Ampro Corporation ReadyBoard 700 Especificações

ReadyBoard 700Single Board ComputerQuickStart GuideP/N 5001723A Revision C

Chapter 1 Setting Up the ReadyBoard 7006 QuickStart Guide ReadyBoard 700Skip any of the following steps that do not apply to your situation.6) Conne

Chapter 1 Setting Up the ReadyBoard 700ReadyBoard 700 QuickStart Guide 78) Connect USB 2 & 3 Cable Assembly• Connect the USB 2 & 3 cabl

Chapter 1 Setting Up the ReadyBoard 7008 QuickStart Guide ReadyBoard 700Connecting Peripherals10) Connecting the peripherals• Connect the keyboard

Chapter 1 Setting Up the ReadyBoard 700ReadyBoard 700 QuickStart Guide 9Applying Power to the ReadyBoard 70013) Check/Set the Power Supply Input Vo

Chapter 1 Setting Up the ReadyBoard 70010 QuickStart Guide ReadyBoard 700a) Select the BIOS andHardware Settings menu asshown in the figure to therig

Chapter 1 Setting Up the ReadyBoard 700ReadyBoard 700 QuickStart Guide 11NOTE The ReadyBoard 700 ships from the factory configured for CRT supportonly

Chapter 1 Setting Up the ReadyBoard 70012 QuickStart Guide ReadyBoard 700

ReadyBoard 700 QuickStart Guide 13Chapter 2 Installing ReadyBoard 700 OptionsThe procedures in the first part of this chapter describe how to install

Chapter 2 Installing ReadyBoard 700 Options14 QuickStart Guide ReadyBoard 700CAUTION To prevent damage to the SODIMM, do not touch the SODIMM until yo

Chapter 2 Installing ReadyBoard 700 OptionsReadyBoard 700 QuickStart Guide 15 45 Angle° Retaining LatchesSODIMMSODIMM Socket (DIMM1)RB70

ii QuickStart Guide ReadyBoard 700Notice PageNOTICENo part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system,

Chapter 2 Installing ReadyBoard 700 Options16 QuickStart Guide ReadyBoard 7005. Remove the existing SODIMM from the SODIMM socket before continuing.Re

Chapter 2 Installing ReadyBoard 700 OptionsReadyBoard 700 QuickStart Guide 17CompactFlash InstallationThe CompactFlash interface allows you to substit

Chapter 2 Installing ReadyBoard 700 Options18 QuickStart Guide ReadyBoard 700NOTE To simplify this procedure, power down the system and disconnect the

Chapter 2 Installing ReadyBoard 700 OptionsReadyBoard 700 QuickStart Guide 197. Insert the CompactFlash card into the socket provided by the tabs on t

Chapter 2 Installing ReadyBoard 700 Options20 QuickStart Guide ReadyBoard 700 RB700_02daU29U28U27U26U25D12D11Q6Q7Q5D9D10Q10Q9U24U23Q8U22

Chapter 2 Installing ReadyBoard 700 OptionsReadyBoard 700 QuickStart Guide 21CAUTION To prevent damage to the ReadyBoard 700 or the CompactFlash card,

Chapter 2 Installing ReadyBoard 700 Options22 QuickStart Guide ReadyBoard 700Installing Software, Drivers, and UtilitiesTo install the operating syste

Chapter 2 Installing ReadyBoard 700 OptionsReadyBoard 700 QuickStart Guide 234. Install any special OS drivers not found on the manufacturer’s diskett

Chapter 2 Installing ReadyBoard 700 Options24 QuickStart Guide ReadyBoard 700

ReadyBoard 700 QuickStart Guide 25Appendix A Technical SupportContacting SupportAmpro Computers, Inc. provides a number of methods for contacting Tech

ReadyBoard 700 QuickStart Guide iiiContentsChapter 1 Setting Up the ReadyBoard 700...

Appendix A Technical Support26 QuickStart Guide ReadyBoard 700

Contentsiv QuickStart Guide ReadyBoard 700Figure 2-6. Removing the CompactFlash Card ...

ReadyBoard 700 QuickStart Guide 1Chapter 1 Setting Up the ReadyBoard 700Using this GuideThis guide provides the most efficient way to set up your Read

Chapter 1 Setting Up the ReadyBoard 7002 QuickStart Guide ReadyBoard 700Setup StepsIt is important to follow the setup steps in this section in the e

Chapter 1 Setting Up the ReadyBoard 700ReadyBoard 700 QuickStart Guide 3Connecting Cable AssembliesConnect the cables provided with the ReadyBoard 700

Chapter 1 Setting Up the ReadyBoard 7004 QuickStart Guide ReadyBoard 700 RB700_10aFloppy Drive Only Cable(26-pin (J20) to 34-pin Flop

Chapter 1 Setting Up the ReadyBoard 700ReadyBoard 700 QuickStart Guide 55) Connect the Serial 3 & 4 Cable assembly• Connect the Serial 3 &a